Goat Milk Soap Making

Super fatting Soap - This means that oils have been left in the soap unconverted by the lye either because the amount of lye was decreased to allow some oil to remain or oil was added at the trace stage after the mix had saponified. Adding the extra oil at this time keeps it in its natural state, and ready to instantly moisturize your skin as you use the soap.

Trace - The point at which the soap/lye mixture begins to thicken. As it becomes the consistency of gravy the essential oils, super fatting oils, botanicals etc are added. The mixture is then poured into a mold to harden.

Cold Process Goat's Milk Soap

Makes 4 lbs. Weigh all ingredients.

16 oz. goat milk (cold)
6.5 oz. lye (sodium hydroxide)
8 oz.palm oil
17 oz. coconut 76 oil
17 oz. olive oil
1 oz grapefruit seed extract
2-3 ozs. essential oil  

Add the lye to the goat milk and watch as it turns a tan color.  Stir in all the lye.  Let sit about 10 minutes.  Don't be concerned about the temperature of the lye mixture or oils mixture.  Prepare your oils, add lye/goat milk mixture to the oils.  The lye/goat milk mixture will look curdled, stir and add it to the pot of oils.  Using a stick blender mix well and continue through to trace.  Add grapefruit seed extract as a preservative and any scent you like.  We've chosen Ginger Essential Oil for a wonderful "Zen" scent.  Pour into your mold, cover and let set 20-24 hrs.  Cure cut soap for 6 weeks.  

Goats milk soap has a creamy smooth texture and is very nourishing for your skin.

INSTRUCTIONS FOR COLD PROCESS SOAP- BASE RECIPE I

This is an easy, mild olive oil soap, good for beginners.

Recipe: (Makes 8 lbs.)

24 oz. olive oil
24 oz. coconut oil
38 oz. vegetable shortening (Crisco)
12 oz. lye
32 oz. distilled water
3-4 oz. any essential or fragrance oil  

• Scale that weighs in pounds and ounces
• Large one-gal. stainless steel or enamel pot (use this exclusively for soap-making)
• Two plastic pitchers, 2-3 qt. size
• Hand stick blender (optional, but makes tracing much easier)
• Plastic measuring cup 2-3 cup size
• Two wooden or plastic spoons (one for the lye and one for the oils.  Use these   exclusively for soap-making)
• Two kitchen thermometers (one for the lye and one for the oils - must read to  over 100 degrees)
• Rubber gloves
• Safety goggles
• Clear plastic container with snap-on lid 8" x 11" x 3" deep, or wooden soap mold      lined with freezer paper
• Large piece of cardboard the size of the wooden mold - used as a lid
• Old blanket
• Freezer paper or plastic garbage bags

Remember:  Be sure to allow for the weight of the containers. Lye (Sodium Hydroxide NaOH)  All ingredients should be weighed.

Begin by putting on your goggles and rubber gloves and weigh out 12 ozs. of lye into one of the plastic containers.    Weigh out 32 oz of distilled water into the other container.  Slowly and in a steady stream pour the lye into the water, stirring until dissolved.  Do this in a well ventilated area and try not to splash.  Let the lye/water mixture sit until the temperature reaches between 90-100 degrees.  This may take several hours, but if you're in a hurry you can place the container in a cold water bath to bring down the temperature quicker. 

In the meantime, get your oils ready by weighing out 24 oz. of coconut oil and 38 oz. of vegetable shortening and placing them into your pot.  Heat them up just until they melt and then remove from heat and add the 24 ozs. of olive oil.  Stir to incorporate and put one of the thermometers into the pot to check the temperature.  The oils will also have to be between 90-100 degrees. Both the lye/water mixture and the oils will have to be at the same temperature before incorporating them.

Prepare your additives.  Start with just 3-4 ozs. of essential oil or a combination of essential oils (blend).  *Note- (some essential oil scents are stronger, so use less, some are lighter and you may add more depending on your preference).  Also, measure 1/4 cup of any dried herbs or flowers (optional).  Its best to start simple for your first batch.  You can also add 1-3 tablespoons of pigment (optional) for coloring. 

Grease the clear plastic container that you're using as your mold and place a piece of freezer paper on the bottom of the container for easy release OR line the container with a plastic garbage bag.  If you are using our wooden soap mold, line it with freezer paper.

Check the temperature of the lye and oils.  When they reach between 90-100°, its time to "make soap."  Slowly pour the lye/water mixture into the oils, stirring continuously.  You may continue to stir using a spoon or switch to the stick blender.  Stir or blend in all the lye and you will begin to see the mixture thicken.  Just as the mixture thickens to the point where you see tracks or "trace" in the soap, add  essential oils and any dried ingredients or colorants.  Remove about 2 cups of the mixture and add the colorant to the 2 cups.  Then add that back into the pot.  Continue to stir or blend until you see designs on the top of the soap (this is known as tracing and can happen in 10-40 minutes depending on the temperature of your mixture).  Quickly add the mixture to the mold.  Cover with the lid.  *Note* if the soap mixture does not fill the mold to the top, place a piece of freezer paper  on top of the soap and then put the lid or a piece of cardboard on the container.  This will prevent soda ash.  Wrap in blankets and place in an undisturbed area for 18 hrs.   Remove the blankets and lid and leave the soap in the mold for another 12 hrs. 

You should have a nice hard block of fresh soap which you can now remove from the mold.  Let the block of soap sit for a day to firm up or slice into bars or chunks immediately. Then place bars in an open box or drying rack for 6 weeks or longer. Don't allow the bars to touch one another.   The soap should be cured completely after 6 weeks, but the longer it cures, the milder and harder it will be. 

Tip: We offer many helpful books on the subject of cold-process soap-making. Good instruction and preparation is the key to being  successful with your first batch.   

Good Luck, and happy soaping!